CountryPainting & Tile Call (435) 979-7134
Weathered boards half-stained a warm brown, the before and after on one wallStock photo

Deck, fence & wood staining in Logan, UTGrey boards. Warm wood again.

We stain decks, fences, wood siding, trim and doors.

The grain shows through and the wood gets its color back.

Deck, Fence & Wood Staining

Stain or paint: what’s the difference

Paint sits on top of wood as a film.

Stain soaks into the fibers, so the grain still shows through the color.

That makes stain a natural fit for decks, fences, siding and doors, where the wood is the look.

Before any stain goes on, the wood has to be clean, sound and dry.

Grey, weathered surface fibers get cleaned or sanded back first.

Brushing stain onto fence picketsStock photo

Signs it is time

Signs your wood needs stain

  1. Boards turning grey

    Sun breaks down the top layer of bare wood and turns it silver-grey.

    Stain brings the color back.

  2. Water soaks right in

    Sprinkle some water on the deck.

    If it darkens the wood right away instead of beading, the old finish is gone.

  3. Splinters and rough spots

    Dry, weathered boards get rough underfoot.

    A good sanding before stain makes the deck nicer to walk on.

  4. Patchy, worn color

    Traffic paths and sunny sides wear first and leave the deck two-toned.

    Even prep brings it back to one color.

  5. A blotchy fence

    Sprinklers and sun hit a fence unevenly, so one stretch fades faster.

    A fresh coat gives the whole run one color.

How the job runs

How a staining job runs

  1. 01

    Look at the wood

    We check the boards, the old finish and how dry the wood is.

    Then we talk color, from see-through tones to solid.

  2. 02

    Clean and prep

    Dirt, grey fibers and loose old finish come off.

    Loose boards or popped nails get pointed out so you can decide.

  3. 03

    Apply the stain

    Stain goes on in even passes, worked along each board so it soaks in without lap marks.

  4. 04

    Walk it and clean up

    We walk the job with you once it’s dry to the touch, then clean up.

    Keep traffic off until we say it’s ready.

Brush laying finish onto raw cedar postsStock photo

Cache Valley

Staining wood in Cache Valley weather

At about 4,500 feet, strong sun and dry summer air pull color and moisture out of bare wood.

Boards go grey and start to check.

Freezing winters add to it, since water that gets into open cracks freezes and pushes them wider.

A sound coat of stain helps water bead off.

FAQ

Questions about staining

Still unsure? Call or text (435) 979-7134 and ask us straight.

How do I get a staining estimate?

Call or text (435) 979-7134 with photos of the deck, fence or wood you want stained.

We’ll set a time to look, and the estimate is free.

Should I stain or paint my deck?

Stain soaks in and shows the grain; paint covers it with a film.

Ask on the call and we’ll talk through both for your deck.

Can you stain doors and trim too?

Yes. Wood entry doors, trim and wood siding can all take stain.

We’ll look at what’s on there now before we pick a product.

What stain do you use?

Ask on the call and we’ll tell you how we’d handle it on your wood.

The right product depends on what’s on the boards now.

Free estimate

Tell us about the job.

Tell us what you want painted, stained or tiled.

Photos help a lot.

We will call or text you back to set a time to look.

  • Call or text (435) 979-7134
  • Based in Logan, UT 84321. Serving Logan and the surrounding areas.
  • Estimates are free and by appointment. We speak English and Spanish.

Request a Free Estimate

Please add your name.
Please add a 10-digit phone number.
That email doesn’t look right.

We only use your details to answer you. Rather talk? Call or text (435) 979-7134.

Call Text Free Estimate